Common sense of fishing rod

Thank you for choosing the products from Falai fishing tackle Company. In order to help you use the products correctly, please read the following notes first and keep this brochure for later reference.

1. Based on the present manufacturing technique of fishing rod, neither glass fiber nor carbon fiber, it is impossible to completely remove the possibility of bending in every section.
2. Especially for the fishing rod made by carbon fiber, due to its strong tenacity, the rod itself will not droop. But comparing to the rod made by glass fiber, it will more or less bend. However, this does not affect its intensity and performance.

■ Extension rod
1、 Uncover the cap of guide, and drill the fishing line through the bottom guide to the top guide.
2、 Section by section pull out the fishing rod from top, and screw the joint of two sections till they are tightly fixed.
3、 When fully pulling out the rod, align all the guides.
4、 After use, loosen the joints in B section and draw in the fishing rod section by section from end.

■ Insertion rod
1、Insert the end section into the second section, the second section into the third section, and into B section, etc., screw the joint of two sections till they are tightly fixed.
2、Fix the fishing line reel, pull out the line and drill it from bottom guide to the top guide.
3、After use, loosen the joints in B section and draw in the fishing rod section by section from end.
4、To avoid becoming flexible, there is a 4-5mm gap between every connection. Please don't forcibly insert the section.

1、Remove the cap of guide along a line, otherwise it may break the fishing rod.
2、Remember to drill fishing line through every guide. Any guide missing drilling may result in breaking the top end.
3、If the fishing line is in disorder, don't draw the line forcibly. Dragging too forcibly on any point of the fishing rod may result in the break of fishing rod.
   ...........................................................................

1、 Take off the plug on fishing rod, pull out the top a little.
2、Pull out the rod section by section, and screw the joint of two sections till they are tightly fixed.

■ Extension rod
1、After use, loosen the joints in B section and draw in the fishing rod section by section from end.
2、Attention should be paid when drawing in to avoid pulling too forcibly, which may hurt your hand.
3、Draw in the fishing rod from B section by turns. If in reverse, the end section may fall into other sections, and maybe cause damage to fishing rod.

■ Insertion rod
1、When draw in the fishing rod after use, loosen the joints by holding the two sides of joint and pull out while screwing, and draw in by turns.

Attentions on using fishing rod without guide

1、Remove the cap of guide along a line, otherwise it may break the fishing rod if screwing too forcibly. Bending the fishing rod too forcibly or using fishing line when it is in disorder may cause break of fishing rod.
  ...........................................................................

1、How to prevent lacquer scaling off
If you seal up the damp or sordid fishing rod, the moisture will possibly cause the bubbling or scaling off of lacquer. To prevent this, always rub off the moisture on fishing rod and keep it in a ventilated place.
2、How to prevent corrosion and rusting
If you seal up the sordid fishing rod, it may cause fading of galvanization and other painted surface, and cause the corrosion and rust of metal parts, thus cause malfunction of fishing rod. Therefore, always remember to rub off the moisture, salt and dirt before storage.
3、Don't remain the fishing rod in the back carriage of car too long time. The long time sealed and high temperature condition is harmful for fishing rod.

The use of brush, toothpaste, gasoline, dope and other organic substances to clean the fishing rod is not allowed, otherwise it may occur damage to rod surface and even the rod itself. Don't clean the rod by steel brush. You shall gently remove the dirt by towel dipped with water, and after it is dry, brush up with car wax or leather.

1、Our company is not responsible for the damage caused by customer's reassembly by their self-determination during repair period.
2、If the products need repairing, the vendor will provide the repair service. But the complete set of products, including damaged part, must be provided to the vendor.。
3、When repairing the product, please bring the repair card with you.
...........................................................................

■ Extension rod
The main cause of the joints fixed too tightly is extending the rod too forcibly. When the joints are fixed too tightly, hold the anti-sliding place near joints, screw and press them in reverse direction to loosen the joints. Pay attention not to press too forcibly, which may hurt your hands.
■ Insertion rod
Hold the anti-sliding place near rubber seat or rubber wheel near joints, and screw and pull them in reserve direction in order to loosen the joints.
■ Extension rod without guide
Remove the plug of B section, pull out the fixed two sections. Then put the rod vertically on a not-too-hard plain ground (or put towel or other soft material on the ground), hold the fixed joints and knock the ground.

1、When using the fishing rod, special attention shall be paid to the electrical shock potentiality by high voltage wire and thunder. Carbon fiber is high electricity-conductive material, so it is very dangerous if it touches electrical wire. The use of fishing rod under high voltage wire is also strictly forbidden. Electrical shock may also occur when using fishing rod in the vicinity of electrical wire.
2、When using fishing rod outside fishing place, take care of the environmental condition. Don't touch electrical wire.
3、Thunder can also cause electrical shock. When coming across thunder, draw in the fishing rod or stay away from it immediately.

........................................................................... 

Please reassured yourself when using the high quality fishing rod produced by Hangzhou Falai fishing tackle Co., LTD, which leave the factory after being strictly inspected.
Please read these explanatory notes carefully, then you can handle it easily. Your precious idea and suggestion are highly appreciated!